Căutare după Subiect "wear"
Afișează articolele 1-19 of 19
-
Analysis of the PM Bearing – Spindle Contact Using Finite Element Method
(UDJG, 2011)Using PM (Powder Metallurgy) technologies, new antifriction materials based on iron-copper powders with different addition elements were developed. The elemental powder mixtures were compacted at different pressures and ... -
Characterizing the Wear Particles of Intervertebral Disc Prosthesis and their Biological Response
(Universitatea ”Dunărea de Jos” din Galați, 2008)Prosthetic debris is the leading factor causing prosthetic loosening and requiring revision surgery. Wear debris is formed over time with any prosthesis. Factors determining disc arthroplasty survivability are similar to ... -
Dynamics of Hip Artificial Joints Wear
(Universitatea ”Dunărea de Jos” din Galați, 2008)In the present paper the authors try to evaluate, based on the results obtained from experimental and numerical previous studies, the wear evolution in the components of a Total Hip Prosthesis (THP), during the service ... -
Examining the Evolution of Microstructure and ITS Effect on the Mechanical and Tribological Properties
(Universitatea "Dunărea de Jos" din Galați, 2017)This paper investigates the superior frictional performance of Ti-DLC films, by examining the evolution of microstructure and its effect on the mechanical and tribological properties. The superior frictional performance ... -
Failure of a Total Knee Prosthesis Tibial Tray Due to the Fatigue Wear
(Universitatea ”Dunărea de Jos” din Galați, 2006)Some studies report the failure of a tibial insert of knee prostheses due to the subsurface cracking and delamination wear [1]. The present study starts by analysing retrieved total knee prosthesis revealing the loss of a ... -
Mechanical and Tribological Properties of TiCxOy Thin Films
(Universitatea "Dunărea de Jos" din Galați, 2005)The main purpose of this work consists on the preparation of single layered titanium oxycarbide, TiCxOy, thin films, deposited by d.c. reactive magnetron sputtering. The depositions were carried out from a TiC solid ... -
On Tribological Behaviour of Thermo-Chemical Treated Steels after Thermo-Magnetic Treatments
(Universitatea ”Dunărea de Jos” din Galați, 2008)The paper presents an analysis on two grades of steel, subjected to nitrocarburized or nitrided thermo-chemical treatment after different thermomagnetic treatments. Based on the concept of tribosystem, pairs of steel rollers ... -
Prediction of Wear of Acetabulum Inserts Due to Multiple Human Routine Activities
(Universitatea ”Dunărea de Jos” din Galați, 2006)It is difficult to predict the quantitative and qualitative aspects of the wear of the components that allow relative motion due to several factors. First, the prosthetic parts in contact experience a wide spectrum of ... -
Residual Stress and Tribology Behaviour of TiCx Coating Deposited by NPCVD Method
(Universitatea "Dunărea de Jos" din Galați, 2014)In this paper, thin TiCx films were coated by chemical vapour deposition method, and various duty cycles were carried out in order to observe the influence of this parameter on residual stress and tribology behaviours. ... -
Some Experimental Results Concerning the Influence of Surface Coatings on the Wear of Poly-Ether-Etherketone (Peek) Polymeric Gears
(UDJG, 2011)Gears made of general purpose Poly-Ether-Ether-Ketone (PEEK) polymeric material and coated on their flanks with a thin layer of different solid lubricants MoS2, graphite (C), BN and PTFE are tested in relation to wear and ... -
The Application of CRN Coating in Sliding Pairs under Lubrication Conditions
(UDJG, 2011)This work revealed the results of the impact of the formed surface layer CrN and the surfaces layer CrN-steel 46Cr2 “ring” structure. The sliding pairs worked under conditions of lubricating the friction area with Lotos ... -
The Influence of Nano-Particle Additive to Lubricating Oils on the Structure and Properties of Friction Surfaces
(UDJG, 2011)The article considers the influence of the additive in the lubricating oils Cermet, on tribological properties of a friction pair «cast iron – chrome», which is typical for the cylinder-piston unit of engines. It is shown ... -
The Influence of the Thermomagnetic Treatments on the Nitrided Superficial Layers Evolution after Wear Process (III)
(UDJG, 2011)Two types of steel grades were subjected to a nitriding thermo-chemical treatment after the thermo-magnetic treatments. The structural aspects of the superficial layers of these steels are studied after the friction process ... -
The Influence of Waste Composition on the Pumping System Corrosion
(Universitatea "Dunărea de Jos" din Galați, 2017)Wastewater piping systems in urban agglomerations or industrial areas have problems with the wear and tear of equipment and water transport pipelines used. The problems are related to hydromechanics wear and corrosion ... -
The Presence of Hydrogen as Wear Environment for the Mechanical System of the Continuous Casting Equipment
(UDJG, 2010)In the last years the continuous casting of the steel has a tremendous development. In the same time, the casting steel quality requirements become higher. The hydrogen as environment of the casting diminishes the steel ... -
Tribological Behaviour of CO-CR-MO and Uhmwpe the Components of Intervertebral Disc Prosthesis
(Universitatea ”Dunărea de Jos” din Galați, 2006)The Intervertebral Disc Prostheses consist of a modular system and his function is based on low intervertebral friction. As a result of friction forces acting to the spine structures, the intervetebral disc prostheses can ... -
Tribological Characteristics and Formation of Subsurface Structures of Cast FE-CR-C Alloys with Different Content of Copper, under Sliding Friction
(Universitatea ”Dunărea de Jos” din Galați, 2009)Effect of copper contents (0%, 0.4%, and 14%) and modes of heat treatment on initial structure of Fe-Cr-C alloys (C~1.2%, Cr = 17…19%) and subsurface structure of friction layers and tribological characteristics of these ... -
Wear Behaviour of the AL7175 Alloy under Different Bulk Stress States
(Universitatea ”Dunărea de Jos” din Galați, 2008)In what concerns the stresses involved in the process, most wear tests (namely those in the pin on disc and the pin on plate configurations) are usually solely concerned with the stress state in the contact originated by ... -
Wear Prediction of Hip Endoprostheses
(2007)The total hip prostheses can be considered as medical-mechanical devices with established failure. The large domain of common activities induces a wide spectrum of loadings in contact prosthetic parts. The contact conditions ...